A new Clyde 19/24! - Construction
Tringa - Currently being built in Germany by Gisela and Helmut Scharbaum

List of photos

28/12/2006 - Strongback in place
22/01/2007 - Moulds being fitted to strongback
22/01/2007 - Moulds and wood keel in place
22/01/2007 - Wood keel and rudder post
23/01/2007 - Stem fitted
03/02/2007 - Bow view of Stem
18/02/2007 - Laminated frame being glued
18/02/2007 - Laminated frame
18/02/2007 - Fitting frames to moulds
25/02/2007 - Transom
25/02/2007 - Stern view with frames in place
25/02/2007 - Transom being fitted
28/02/2007 - Transom in place
13/05/2007 - Floors and chain plates fitted
16/05/2007 - Frames, floors, and beam shelf in place
16/05/2007 - Floors being fitted
02/08/2007 - Hull planking started
14/08/2007 - More Hull planking
19/08/2007 - More Hull planking
26/08/2007 - Still more hull planking
09/09/2007 - Planking continues
27/09/2007 - View on Wood Keel, planking nearly finished
16/10/2007 - Checking position of Bobstay fitting
24/10/2007 - Hull planking very nearly finished
11/11/2007 - Leading edge of Stem being offered up
17/11/2007 - Start of fairing up
18/11/2007 - Fairing partly finished
25/11/2007 - Fore end faired
25/11/2007 - Aft end faired
29/11/2007 - View of faired hull
29/11/2007 - Bobstay fitting in place
01/12/2007 - First coat of Epoxy
05/04/2008 - Positioning glass cloth for sheathing
05/04/2008 - Glass cloth positioned ready to be wetted out
12/04/2008 - Glass sheathing wetted out
04/05/2008 - After five coats of primer
31/05/2008 - Waterline marked and half way to being turning over
31/05/2008 - Nearly turned over
09/06/2008 - Right way up and in her cradle
09/06/2008 - Inside of bare hull
10/08/2008 - Completing and adjusting the floors and chain plates
10/08/2008 - Completing and adjusting the floors and chain plates
10/08/2008 - Completing and adjusting the floors and chain plates
23/08/2008 - Painting the hull with epoxy
06/09/2008 - Painting the floors and hull white
13/09/2008 - Painting the floors and hull white
21/09/2008 - Glueing the inner floor, which is made of Oak
26/09/2008 - Glueing the mast step, also of Oak
26/09/2008 - Marking out the mast step
28/09/2008 - Mast step ready to be fitted
12/10/2008 - Fitting the mast step
03/10/2008 - Marking out the masthole
03/10/2008 - Fitting the masthole
03/10/2008 - Fitting deck beams
12/10/2008 - Painting sole
18/11/2008 - Fitting bulkhead
24/11/2008 - All beams in place
24/11/2008 - All beams in place
09/11/2008 - Fitting motor and prop shaft
18/11/2008 - Fitting motor and prop shaft
18/11/2008 - Fitting motor and prop shaft
30/11/2008 - Fitting motor and prop shaft
30/11/2008 - Fitting motor and prop shaft
30/11/2008 - Fitting motor and prop shaft
20/12/2008 - Fitting cockpit floor
18/01/2009 - Cockpit sole
28/02/2009 - Saloon, facing aft
22/04/2009 - Sink and electrics panel
12/05/2009 - Deck beams in place
01/06/2009 - Plywood deck partly laid
01/06/2009 - Interior faceing forward
05/07/2009 - Ply deck in place, Margin board in place
24/07/2009 - Laying teak deck
26/07/2009 - Laid deck at bow
01/08/2009 - Laid deck at side
09/08/2009 - Laid deck aft
09/08/2009 - View over laid deck
12/08/2009 - Caulking laid deck
24/08/2009 - View over caulked deck
24/08/2009 - Aft Transom corner - Caulked deck
24/08/2009 - Bow - Caulked deck
27/08/2009 - Transom fairlead
03/09/2009 - Cockpit coaming being constructed
05/09/2009 - Coaming and deck in way of Water filler
07/09/2009 - View over deck from forward
08/09/2009 - Ballast keel on trolley
10/09/2009 - Fitting bowsprit
10/09/2009 - Fitting bowsprit
11/09/2009 - View over deck from bowsprit
11/09/2009 - Cranse iron fitted
20/09/2009 - View over deck from aft, Margin boards varnished
31/05/2010 - Varnished and fitted out cockpit
05/06/2010 - Roll out
05/06/2010 - Completed - Stern view
05/06/2010 - Completed - Profile
05/06/2010 - Completed - View over deck from aft
05/06/2010 - Completed - General view
15/06/2010 - Completed - Foredeck detail